Water Damage Restoration Kent, CT

A failed sump pump, a burst supply line, or storm-driven groundwater can leave inches of standing water sitting against framing, drywall, and stored belongings. The longer it sits, the further moisture wicks up the walls and the faster the Category of the water deteriorates.

Our IICRC-certified technicians classify the water under IICRC S500, then pull the standing water down to the slab with truck-mounted and submersible extraction. We open wet wall cavities, set air movers and LGR dehumidifiers for structural drying, and apply an antimicrobial per IICRC S520 where Category 2 or 3 water is involved.

We take daily Tramex moisture readings and dry the assembly to the ANSI/IICRC dry standard, not to a calendar. Every reading, photo, and scope line is documented for your insurer so the claim moves on facts, not guesswork.

A frozen or failed supply line can let pressurized water run behind walls and ceilings, soaking multiple rooms before anyone finds the source. It starts as clean Category 1 water, but the longer it sits in cavities and against organic materials, the faster it degrades and the wider the damage spreads.

We stop the source first, then extract the standing water and trace how far it has traveled with moisture meters and thermal imaging. We open and dry the affected wall, ceiling, and floor cavities with air movers and LGR dehumidifiers, monitoring the assembly daily so we dry only what is wet rather than tearing out what can be saved.

We dry the structure to the ANSI/IICRC dry standard and confirm it with moisture readings before anything gets closed back up. The scope, daily logs, and photos are documented for your insurer so the claim is backed by data, not estimates.

An overflowing toilet is a Category 3 black-water event under IICRC S500. The water is contaminated, so it cannot simply be dried in place. Once it spreads across the bathroom floor and soaks into baseboard, drywall, and the subfloor, the affected porous materials carry a real sanitation risk, not just a moisture one.

Our IICRC-certified technicians treat it as Category 3 from the first minute, working in full PPE. We extract the contaminated water, then remove the affected porous materials, drywall, baseboard, and flooring as needed, rather than try to salvage them. We sanitize the remaining structure with an EPA-registered antimicrobial per IICRC S520, then run air movers and LGR dehumidifiers for controlled structural drying.

We dry the framing and subfloor to the ANSI/IICRC dry standard and verify it with moisture readings before any rebuild, so new finishes go over a clean, dry assembly. The full scope, sanitation records, moisture data, and photos are documented for direct submission to your insurer.

A storm or a failed flashing detail can let water into the attic, where it saturates sheathing, framing, insulation, and the ceilings and wall cavities below. The intrusion is often hidden until staining appears, and by then the trapped moisture has had time to spread and raise a real mold risk.

We trace and stop the intrusion, adding tarping or temporary protection where the roof needs it, then find the full moisture footprint with meters and thermal imaging. We remove saturated insulation and drywall where required, dry the framing and cavities with air movers and LGR dehumidifiers, and apply an antimicrobial per IICRC S520 where conditions warrant it.

We dry the structure to the ANSI/IICRC dry standard and verify it with moisture readings before any rebuild, so finishes go back over a sound, dry assembly. Every reading, photo, and scope line is documented for your insurer.

When water reaches a hardwood floor, the boards absorb moisture from below and cup or buckle as the subfloor stays wet. Pulling the floor too early wastes a repairable surface, while ignoring it traps moisture against the subfloor and invites rot and mold.

We map the moisture through the boards and subfloor with pin and pinless meters, then set a controlled drying system, floor drying mats, directed air movement, and LGR dehumidification, to draw water out of the assembly. Readings guide whether the floor can be saved in place or needs to come up.

Many cupped floors flatten back out once the subfloor reaches the dry standard, which can save a full tear-out. We document the daily readings and the in-place drying decision so your adjuster sees the rationale behind the scope.