Your policy, your selection.
Your policy is between you and your insurer. Selecting the licensed restoration contractor generally sits with the property owner.

Silver City Fire & Puff Back Cleanup · Soda Blasting Char Removal IICRC S700 · Direct Insurance Billing · 60-Minute Response
Eco-Friendly Solutions For Healthier Spaces
Reviewed by David Megeneishvili·Licensed & Insured In CT·IICRC AMRT + WRT
Fire damage restoration is the ANSI/IICRC S700 documented process of stabilizing a fire-damaged building, classifying the smoke residue, and cleaning it off every affected surface, the contents, and the HVAC system. Residue type decides method. Dry smoke, wet smoke, protein and fuel oil each clean differently, and soot is acidic, so it keeps corroding metal, electronics and finishes until it is removed. Cleaning is followed by source deodorization, HEPA filtration, and verification that the odor is gone rather than covered.
In Meriden, CT, the order is fixed. The fire department releases the scene, then the building is secured and boarded. Water from the suppression effort is extracted and dried first, because soot pressed into wet material sets, and wet cellulose grows mold within days. Residue is typed, then structure and contents are cleaned separately, contents off site where needed. Deodorization runs last, at the source, with the assembly open. Every stage is documented for the carrier.
Connecticut fire work is scoped against ANSI/IICRC S700. The local fire marshal holds the scene until the cause and origin investigation releases it. The cleaning phase is restoration work; the structural repair that follows is home improvement work under Connecticut law, which requires a registered contractor, a written contract, and a permit from the local building department.
Green Restoration works to ANSI/IICRC S700: stabilize first, type the residue before choosing a cleaning method, run HEPA filtration throughout, and treat odor at the source. Ozone deodorization runs only in an empty structure, because no federal agency has approved ozone generators for use in occupied space.
From the Hubbard Park side ranches to the factory-era blocks downtown, Meriden fire losses get one crew for the whole arc: same-hour board-up, suppression-water extraction, soda blasting char removal, pack-out, and rebuild, all under an IICRC AMRT/WRT certified owner and one written S700 scope.
Meriden dispatch is a straight shot on I-691: a certified crew inside the hour with board-up stock, extraction gear, and generator power, whether the address is a Cape on the hill or a factory-era block downtown.
IICRC S700 · 60 minute dispatch · Hamden Mobile HQ
Sodium bicarbonate abrasive blasting strips fire char from joists, sheathing, and masonry chimneys without damaging the substrate underneath. Mohs 2.5 media is softer than wood, FDA GRAS, silica-free, and water-soluble for HEPA-vac cleanup that wire brushing and sanding cannot match.
Sodium bicarbonate · Mohs 2.5 · IICRC S700 aligned
Smoke damage in Meriden requires HVAC decontamination, negative-air containment, and HEPA scrubbing on every affected zone. We coordinate with property managers, condo boards, and adjusters so containment, scope, and access stay aligned across the entire affected footprint.
HVAC decon · Negative-air containment

Same-day plywood board-up of broken windows and doors plus roof tarp-over to secure your Meriden property against weather, animals, and theft while the IICRC S700 restoration scope is finalized.
Whole-home and commercial generators staged on every Meriden fire response when utility power is cut at the meter. We run dehumidifiers, HEPA scrubbers, hydroxyl generators, and temporary lighting off our own diesel and propane gensets so drying, containment, and crew safety continue around the clock without waiting on Eversource to re-energize the service.
Full IICRC S700 puff back remediation for Meriden homes with oil-fired heat. Mechanical room cleanup, NADCA-aligned supply duct rotary brushing, soft-goods laundering, hydroxyl deodorization through every upstairs bedroom, and coordination with licensed CT oil burner technicians so the furnace returns to safe operation before close-out.
Creosote-bonded soot blowback from clogged chimneys, downdrafts, and flue fires cleaned with soda blasting on the masonry, full firebox and damper service, and HVAC riser decontamination where the flue shares a chase with supply ducts. We coordinate with a licensed CT chimney sweep on flue liner inspection before reuse.
Grease fire cleanup for Meriden kitchens including cabinet refinishing, appliance cleaning, soda blasting on charred framing behind drywall, and full structural restoration.
Inventoried, barcoded contents pack-out to our secure climate-controlled storage facility for off-site ultrasonic cleaning, ozone deodorization, and soft-goods laundering. Your Meriden belongings stay in humidity-controlled storage, documented for your insurer, until reconstruction is complete and we pack them back.
IICRC S500 structural drying for fire suppression water. LGR commercial dehumidifiers, moisture mapping, and EPA-registered antimicrobial treatment within the 48-hour mold-prevention window so the fire loss does not become a mold loss on top of it.
Thermal fogging, ozone chamber treatment, and hydroxyl generators neutralize smoke odor at the molecular level throughout the structure. The pH-neutralizing chemistry of our soda blast media also breaks down acidic soot odor compounds at the source, not just behind a fragrance mask.
Single-source reconstruction once mitigation is signed off. Licensed CT contractors handle framing, drywall, electrical re-feed off our gensets, plumbing, hardwood refinishing, and finish carpentry through the Meriden building department permit process. One restoration partner from board-up and generator power through reconstruction handoff means no scope gaps between trades and one closeout file for your carrier.
Meriden Fire Damage Does Not Wait For Morning. 60 Minute Response.
A certified crew reaches Meriden inside the hour and stays yours through the rebuild.
Owner-led IICRC AMRT + WRT certified fire damage response with 60-minute mobile dispatch, soda blasting soot removal, and direct insurance billing across Meriden and Central CT.
Our owner holds IICRC AMRT and WRT certifications and walks every Meriden fire job. The only New Haven County restoration company with an IICRC-certified owner-operator on every major loss.
IICRC S700 certified crews arrive within 45 to 60 minutes across our Hamden service area with board-up materials, roof tarps, HEPA air scrubbers, blast pots, and water extraction equipment.
Sodium bicarbonate char removal on structural framing, joists, sheathing, and masonry chimneys. The only New Haven County crew running soda blasting in-house for Meriden fire damage.
We bill State Farm, Liberty Mutual, Travelers, Chubb, AIG, and every major carrier directly with IICRC documentation, soda blasting protocol records, AMRT clearance records, and contents inventory for Meriden claims.
These are the fire and smoke losses we restore most often, every job run to the IICRC S700 standard with documented cleaning, source odor control, and a record built for your insurer.

In Meriden, a stovetop grease fire in a Hub triple-decker kitchen blackens cabinets and leaves an oily film.
Most home fires start in the kitchen, where a grease or stovetop flare can scorch cabinets, melt fixtures, and drive greasy soot across the ceiling and into adjoining rooms. The residue is acidic, so it keeps etching metal, stone, and finishes for as long as it sits.
Our IICRC S700 crews stabilize the scene, remove unsalvageable material, and clean structural surfaces with the right method for each soot type, dry sponge, solvent, or abrasive, before sealing odor-bearing surfaces. Contents are inventoried and either cleaned on site or packed out for off-site restoration.
Surfaces are cleaned to a documented standard and deodorized so the kitchen does not carry a lingering burnt odor. Every line of scope, photo, and cleaning record is documented for your insurer so the claim moves on evidence.
Scenario 1 of 4: Kitchen Fire Damage
The same local Green Restoration team covers all of these across Meriden. One number for every emergency and every cleanup.
Common range across single-room smoke remediation through whole-home fire reconstruction. Final pricing depends on owner-led inspection.
Four quick questions. Starting figures on this page. No call required.
FLIR thermal scope. Free, no obligation. Owner-led on every fire job.
Ranges shown are starting figures only. Final pricing depends on on-site inspection and carrier coverage. We are not licensed public adjusters.
Meriden burns two different ways: fast kitchen and electrical fires in the post-war Capes and ranches, and slow smoldering losses in the factory-era downtown blocks that load every plaster wall with acidic soot. Both are 72-hour problems. What gets treated in the first three days is what survives.
Acidic Residue Attacks Stone And Metal Fast
Soot is acid. Give it 72 hours and it permanently etches glass, chrome, marble, and stainless, which in a Meriden kitchen fire means the appliances and fixtures that survived the flames get lost to the residue. Fast S700 cleanup is the difference between cleaning and replacing.
Hidden Spread Beyond The Fire Room
A single-room fire on the Pratt Street downtown corridor or Silver City pushes smoke through wall cavities, return-air plenums, and shared HVAC trunks within minutes. Without negative-air containment and HEPA scrubbing, adjacent rooms are contaminated by soot the original fire never reached.
Pre-War Urban Triple-Decker, Victorian, Run Oil Burners
Oil heat is still common in Meriden's older housing, and a burner ignition failure can push a cloud of oily soot through every supply register in minutes. Mechanical room, ductwork, and upper floors all need S700 remediation before the film bonds to plaster and woodwork.
Mold Colonizes In 48 Hours Unsealed
What the hoses put in has to come out fast: drywall, subfloor, and insulation hold suppression water invisibly, and past 48 hours the S500 drying window closes and mold colonizes the burned-out cavities. That turns one insurance claim into two. WRT-led structural drying starts the same day for exactly that reason.
Flue Downdraft Or Liner Failure
A clogged flue or liner failure sends a chimney puff back through the firebox and adjacent rooms. Creosote-bonded soot etches brick, fieldstone, and stone hearths within days. Without soda blasting on the masonry and a licensed CT sweep liner inspection, the next fire risks restart inside the chase wall, common in older Meriden stock along Cathole Mountain ridge and Hanover.
Eversource Or UI Service Cut At The Meter
Meriden Fire Department often pulls the meter on a structural fire, and Eversource or United Illuminating re-energization runs days to weeks. Without site generators running dehumidifiers, HEPA scrubbers, and hydroxyl machines, drying and odor work stalls. Our trucks roll with diesel and propane gensets so work continues.

Meriden pre-war urban triple-decker, Victorian, and mill housing stock along the Quinnipiac River valley and former Silver City manufacturing corridor each create fire patterns that DIY cleanup and surface-only methods cannot solve. IICRC S700 response with in-house soda blasting led by an IICRC-certified owner is the durable fix.

Our owner holds personal IICRC certifications in Applied Microbial Remediation (AMRT) and Water Restoration (WRT). The only New Haven County restoration company where the owner walks every fire job and signs the IICRC documentation that goes to your adjuster.
A crew is on site in Meriden within 45 to 60 minutes of your call, day or night, dispatched across our Hamden service area. Same-visit board-up, tarp-over, and fire suppression water extraction begin immediately so the loss stops compounding while your adjuster is still being assigned.
Green Restoration runs Econoline blast pots, sodium bicarbonate media, and trained operators in-house, the only New Haven County restoration company with soda blasting capability on the truck for fire jobs. Meriden factory-era framing, Victorian joists, and masonry chimneys are all candidates for source-removal char cleanup that wire brushing cannot match.
We bill State Farm, Liberty Mutual, Travelers, Chubb, AIG, Safeco, and every other major carrier directly with IICRC documentation, timestamped photos, soda blasting protocol records, AMRT clearance records, and contents inventory so your Meriden claim closes fast.
Soda blasting is the difference between a fire-cleaned Meriden property that stays clean and a property that smells like smoke six months later. Meriden factory-era framing and Hub masonry absorb fire soot into the substrate itself, where sanding and wire brushing cannot reach without driving carbon deeper. Our IICRC S700 crews run sodium bicarbonate abrasive blasting in-house on every fire job that needs source removal on structural surfaces, with AMRT-led mold prevention running in parallel.
Pharmaceutical-grade baking soda. Softer than wood (Mohs 4) and original lath, harder than soot bond layer. Friable on impact, shatters into dust on contact with the substrate rather than embedding into grain or finish.
IICRC S700 fire protocol and S520 mold protocol both list abrasive blasting as a recognized source-removal method for porous structural wood, charred framing, joists, and sheathing where wire brushing leaves residue.
Same compound used in food and pharmaceuticals. No crystalline silica, no toxic residue, no respirable lung hazard beyond standard PPE. Non-sparking and non-flammable on partially-cleared fire scenes.
Meriden's factory-era blocks and older Victorians were built with true-dimension lumber and lath-and-plaster assemblies that deserve better than a grinder. Bicarbonate blasting is the gentler physics: media softer than the substrate, shattering on impact, carrying the char off as dust that rinses away. Odor goes with it, neutralized chemically rather than masked. What sanding and wire wheels destroy, soda leaves standing.
On Meriden fire jobs we typically deploy soda blasting on three substrates: charred dimensional framing and ceiling joists where the fire reached structural wood, brick or stone masonry chimneys with creosote-bonded soot, and sheathing behind blown-out drywall where a stain-blocking primer alone will not contain odor. Plaster walls and finish surfaces get IICRC S700 dry-sponge cleaning first, then a test patch decides whether selective soda blasting or full repaint is the right call. Our IICRC AMRT and WRT certified owner signs off on every blast scope.
Sodium bicarbonate residue is water-soluble and FDA GRAS, so post-blast cleanup is HEPA vacuuming followed by a damp wipe with a microfiber towel, then a final pass with EPA-registered antimicrobial under IICRC AMRT protocol to address any mold spores exposed by the char removal. We document moisture content on cleaned framing back to under 16 percent before any new sheathing or drywall goes up. In older Meriden homes along the Quinnipiac River valley and former Silver City manufacturing corridor, that 16 percent moisture gate is the line between a clean rebuild and a callback.

Meriden fire calls split between the residential hill neighborhoods and the factory-era downtown blocks, and the fleet loads for both: blast pots and scrubbers for structural work, contents crates for smoke losses, negative-air machines for multi-unit containment.
Every Meriden response truck is staged with the full IICRC S700 fire kit, soda blasting setup, contents pack-out crates, and structural drying equipment so a single dispatch handles board-up through reconstruction handoff.

Response reaches Meriden in 45 to 60 minutes via I-91, I-691, or Route 15. Multi-family and mixed-use downtown buildings get containment first so soot stops migrating between units, then extraction and drying. Single-family Capes and ranches usually start straight at stabilization and extraction. The owner attends every major loss.
The constant across Meriden's housing mix is the protocol: one IICRC S700 scope, one crew, one documentation file to the carrier. What changes by neighborhood is only the order the equipment comes off the truck.
From the first call to final walkthrough, every step is documented, insured, and owner-supervised.

Full service fire damage response, soda blasting soot cleanup, contents pack-out, and reconstruction for Meriden homes and businesses. 60-minute emergency dispatch across New Haven County, day or night.
Green Restoration provides IICRC S700 certified fire damage restoration and soda blasting soot removal in Meriden, CT, serving neighborhoods including West Side, East Side, Hub, South Meriden, Silver City, and Hanover Pond. Dispatched across our Hamden service area with direct access via I-91 and the Wilbur Cross Parkway, our certified technicians are on site within 45 to 60 minutes of dispatch with board-up, tarp-over, soda blast pots, and contents protection.
As a locally based Green Restoration franchise, we know the fire conditions Meriden properties face along the Quinnipiac River valley and former Silver City manufacturing corridor: Hub and Curtis Street triple-decker multi-family fires, Silver City Victorian oil burner puff back, and Hanover Pond industrial brick-loft electrical events. The owner personally walks every major loss and coordinates directly with adjusters from State Farm, Travelers, Liberty Mutual, Chubb, and all other major carriers.
We are not licensed public adjusters and do not negotiate claims on your behalf. We submit IICRC S700 scope documentation directly to your insurer.
60-minute emergency dispatch, 24/7/365.
(203) 742-0542Request Free InspectionIICRC S700 · Licensed & Insured · All Insurance Accepted
Mobile dispatch across all Hamden service area neighborhoods and Central CT.
Crews dispatched within 45 to 60 minutes across Meriden and Central CT. Board-up, soda blasting source removal, contents pack-out, and reconstruction managed end to end by our IICRC AMRT + WRT certified crew.
Crews on site within 45 to 60 minutes across our Hamden service area with board-up, HEPA scrubbers, blast pots, and generator power for Meriden.
Our owner personally holds IICRC AMRT (mold) and WRT (water) certifications and walks every Meriden fire job.
We file scope documentation and itemized estimates directly with major carriers. Not licensed public adjusters.
Econoline blast pots and sodium bicarbonate media run by trained operators on every fire job that needs source removal.


Your Meriden Fire & Smoke Damage Specialists Since 2014
Green Restoration provides IICRC S700 certified fire and smoke damage restoration, soda blasting soot cleanup, contents pack-out, and reconstruction for homes and businesses in Meriden, CT. Our process focuses on rapid stabilization, hospital-grade soot removal, molecular odor treatment, and documented reconstruction. We work with property owners and insurance providers to document scope clearly and restore affected areas the right way, without unnecessary steps or delays.
“As the local co-owner across our Hamden service area, I am IICRC certified in water restoration (WRT) and mold remediation (AMRT). Every Meriden fire job is personally overseen, documented for your insurer, and stays open through soda blasting clean-up and reconstruction until lab-verified clearance confirms the work is complete.”
Connecticut policyholders generally have the ability to select their own licensed restoration contractor. Carriers and contractors work the same claim process together.
Your policy is between you and your insurer. Selecting the licensed restoration contractor generally sits with the property owner.
Carrier referral and preferred-vendor programs are offered to streamline claims. You can use a referred contractor or retain a different licensed contractor.
Referred or independent, we submit IICRC S700 documentation, photo-logged inventory, and itemized line items directly to your adjuster.
If you bring in a different licensed contractor mid-project, the scope and remaining work are documented at handoff so the claim continues without gaps.
Educational reference only. We are not licensed public adjusters and do not negotiate claims on your behalf. Coverage and process specifics live with your carrier and your policy language.
4.9 out of 5, Rated by your neighbors on Google
We discovered mold when removing our pellet stove and called Green Restoration for help. David was very communicative and helpful throughout the entire process. He did the job thoroughly and professionally. Highly recommended!
David Woolner
Mold RemediationI had a fantastic experience with Green Restoration. From start to finish, the team was professional, thorough, and extremely knowledgeable. David came for the initial inspection and took the time to explain the entire process.
Annmarie Gieparda
Mold RemediationWe had mold due to a water leak in our half finished basement. David and his crew did a great job, we were very satisfied. I would highly recommend Green Restoration to anyone.
Tanya
Water DamageI needed my entire condo completely cleaned after a soot blow back. Green Restoration was top shelf! So thorough and professional. Thank you so much!
Jacki Hornish
Fire & Soot CleanupInstant estimate for emergency response, soda blasting soot cleanup, contents pack-out, and reconstruction in Meriden and Central CT. Owner-led inspection on scope above $25,000. Transparent pricing, direct insurance billing.
Ranges based on IICRC S700 fire jobs we have handled across New Haven County, drawn from 2 verified Google reviews (5.0★) and our internal job-cost ledger. Final pricing depends on on-site inspection.
Smoke, Soot & Puffback
$1,500 to $8,500
Furnace puffback, chimney smoke, soot or nicotine odor cleanup, no structural burn
Contained Fire + Smoke
$8,500 to $45,000
Single-area burn with house-wide smoke, soot and suppression water cleanup
Major Structural
$45,000 to $150,000+
Multi-room structural loss with demolition, odor sealing and full reconstruction
Priced by scope: what burned, and how far the smoke traveled. Read the full cost guide.
Clear, honest answers about emergency fire response, soda blasting, IICRC certifications, and insurance coverage in Meriden, CT.
Smoke, soot, and puffback cleanup with no structural burn typically runs $1,500 to $8,500, and it is the most common fire-family job we handle in Meriden. A contained fire with house-wide smoke damage runs $8,500 to $45,000, and major structural restoration with reconstruction runs $45,000 to $150,000 and up. Smoke travel, soot type, and suppression water place a loss inside its tier. Assessment is free and produces a written line-item scope we submit directly to your insurer. We are not licensed public adjusters and do not negotiate claims on your behalf.
Coming through the Hamden service area on I-91 or I-691, a certified S700 crew is on a Meriden fire in 45 to 60 minutes at any hour. Major losses get the owner on the first walk. (203) 742-0542 answers around the clock.
Soda blasting uses sodium bicarbonate at Mohs 2.5, softer than wood, plaster, or original lath, so the abrasive shatters into water-soluble dust on impact instead of embedding into the substrate. The factory-era Meriden blocks and older Victorians carry original lath and true-dimension framing that no one wants ground down with wire wheels. Bicarbonate at Mohs 2.5 is softer than all of it: the media shatters on impact, carries the char off as water-soluble dust, and leaves the substrate intact and chemically deodorized rather than polished black.
Plan on roughly $3,500 for a contained single-room smoke loss in a Meriden Cape or ranch, and up to $80,000 or more where a whole-home loss adds structural soda blasting, duct decontamination, pack-out, and rebuild. Ranges based on jobs we have handled across Central CT. We provide a written IICRC S700 scope estimate on-site after thermal imaging and soot density mapping, with the owner present for any scope above $25,000.
Connecticut homeowner policies cover fire damage at replacement cost in Meriden, subject to your policy terms and deductible. We submit IICRC S700 documentation, soda blasting protocol records, and contents inventory directly to your carrier. We are not licensed public adjusters and do not negotiate claims on your behalf, but we provide the scope documentation your adjuster requires.
Two personal certifications ride on every Meriden fire scope: our owner holds IICRC WRT for the suppression-water side and AMRT for the mold risk that follows it, and signs the documentation himself. The company is an IICRC Certified Firm operating under CT HIC.0668405.
Figure 5 to 10 days for a contained kitchen fire in a Meriden Cape or Colonial. When smoke has loaded the plaster or an oil burner has puffed back through the ducts, 10 to 21 days. A whole-home loss with structural soda blasting, rebuild, and Meriden building department permits runs 30 to 90 days. Soot density, suppression water, and reconstruction scope set the pace.
Yes. Furnace puff back and chimney puff back are separate scopes and we run both in Meriden. On the furnace side: the mechanical room gets decontaminated, supply ducts cleaned to NADCA-aligned standards, upper-floor soft goods laundered, hydroxyl deodorization run, and a licensed CT oil burner technician clears the unit before reuse. On the chimney side: soda blasting on the masonry, firebox and damper service, flue liner inspection through a licensed sweep, plus riser decontamination where flue and supply ducts share a chase. Everything is documented to IICRC S700.
Meriden Fire Department pulls the meter on structural fires as a matter of course, and utility re-energization is measured in days, sometimes weeks. Our answer is generator power on every truck, diesel and propane both, so drying, HEPA scrubbing, hydroxyl deodorization, and site lighting never pause. The 48-hour S500 drying window does not care when the utility shows up, so neither do we.
Three reasons Meriden owners hire us: the certifications are personal, not just corporate, with a WRT + AMRT certified owner walking the job; the soda blasting is in-house, not subcontracted, which no other New Haven County restoration company offers; and the file your adjuster gets is complete on the first submission. Trucks stage HEPA scrubbers, hydroxyl generators, contents crates, and blast pots on every response. One call: (203) 742-0542.
Yes. Salvageable contents from a Meriden fire get barcoded, photographed, packed out, and held in climate-controlled storage while the property is restored. Smoke-loaded soft goods and electronics are cleaned and deodorized off-site rather than on a folding table in the driveway, and the whole chain, pack-out through pack-back, is documented for your insurer. Call (203) 742-0542 to schedule it.