Mold RemediationResidential

Multi-Area Mold Remediation in a Darien Residence

Darien, CTSeptember 2024Mold Remediation
Mold remediation project documentation in Darien, CT, photo 11 / 5

Mold remediation project documentation in Darien, CT, photo 1

S520-15
Standard
6-mil
Containment
Plant-based
Antimicrobial
5
Photos in record
Initial Assessment

What Happened

A Darien, CT homeowner reported mold growth across multiple areas of the property. Following inspection and confirmation by an independent hygienist, Green Restoration was engaged to remediate under ANSI/IICRC S520-15 standards using eco-friendly, plant-based solutions. Containment was established before any disturbance to prevent cross-contamination, and HEPA-filtered negative air ran continuously through the project.

Damage Inventory

Scope of Damage

Affected Rooms

Moderate

Multiple areas of the residence treated. Visible mold growth on framing, drywall, and surface materials. HEPA vacuuming and bagged-out disposal of porous contaminated materials.

Containment Zone

Severe

6-mil critical containment with airlocks installed at affected entries. Negative pressure verified throughout.

Surrounding Space

Light

Adjacent rooms inspected for cross-contamination. Surface cleaning and antimicrobial application as preventive treatment.

Restoration Process

How We Solved It

  1. 1

    Hygienist-Guided Scope

    Independent third-party hygienist report reviewed. Scope mapped against IICRC S520-15 condition categories before any work began.

  2. 2

    Containment & Airlocks

    6-mil plastic containment barriers and airlocks installed at affected zones. Negative pressure verified before disturbance.

  3. 3

    HEPA Vacuuming

    Detailed HEPA vacuuming of all surfaces. Loose substrate removed and bagged out under containment.

  4. 4

    Plant-Based Antimicrobial

    EPA-registered plant-based antimicrobial applied per label dwell time. No bleach used in occupied spaces.

  5. 5

    Negative Air Throughout

    HEPA-filtered negative air machines ran continuously to capture airborne particulates and prevent cross-contamination.

  6. 6

    Post-Remediation Verification

    Containment held until clearance air sampling confirmed spore counts within target threshold of outdoor control. Project signed off.

Equipment On-Site

Tools & Equipment Used

HEPA AFD (negative air)
HEPA vacuum
6-mil containment + airlock kit
Plant-based antimicrobial fogger
LGR dehumidifier
Frequently Asked

Questions Homeowners Ask

How long does mold remediation take in Darien, CT?

Most residential mold remediation projects in the Fairfield County area complete in two to four days on-site. Duration depends on the affected square footage, the IICRC S520 condition category, and whether third-party clearance verification is required.

What does mold remediation cost in Darien, CT?

Cost depends on affected area, condition category, and whether containment and a third-party hygienist are involved. Multi-room residential projects in Darien typically range from a few thousand dollars to mid-five-figures. Green Restoration provides a written scope and price after the initial inspection at no cost.

Does insurance cover mold remediation in Connecticut?

Mold may be covered when caused by a covered peril (sudden plumbing failure, accidental water discharge). Long-term moisture intrusion is often excluded. Green Restoration documents every step for your carrier including moisture readings, photos, and a line-itemed scope. We work with insurance, but Green Restoration is independent and not on any insurer's panel.

What is the ANSI/IICRC S520-15 standard?

ANSI/IICRC S520-15 is the consensus-based national standard for professional mold remediation. It defines three condition categories of mold contamination, requires source removal and containment over chemical treatment, and specifies when third-party post-remediation verification is appropriate.

Can I stay in my home during mold remediation?

In most cases, yes, when remediation is contained to specific areas. The Darien project was completed with the homeowner in residence using critical-barrier containment with airlocks. Severe whole-home contamination may require temporary relocation, which the hygienist will determine.

How do I prevent mold from coming back?

Mold returns when the moisture source returns. Address the moisture (failing sump pump, foundation crack, slow plumbing leak, poor ventilation, grade pitched toward the home) then keep ambient relative humidity below 60 percent and inspect annually.

Back to All Case Studies
Local Service Area

Darien is served by
Green Restoration of Fairfield County

(203) 674-9573

Available 24 / 7 for emergency response